Requirement of Active and Passive Air Sampling in Controlled Areas

-

Air sampling is a mandatory procedure to be followed in pharmaceuticals to produce the contamination free quality product.

What would you say if I ask for the causes the most contamination of products during the manufacture of pharmaceuticals?

However, air is another keysource of contaminationthat most pharmaceutical facilitiesoften ignore to take precaution from. Air samplingor air monitoring is essential for Quality Control(QC) purposes especially in companies that manufacture pharmaceutical products in controlled areas or clean rooms with filtered air.Well, what pharmacists, health care practitioners, and microbiologists refer to as air sampling can simply be defined as taking a correct measurement of the practical airborne bacteria, mold, yeast, spores and fungal cells which can be collectively referred to as bioburden in the surrounding air.
The two main methods used to sample air are:
1.Active air sampling/ monitoring

2.Passive air sampling/ monitoring

1. Active Air Sampling

This method is sometimes referred to as pumped sampling where the air in the controlled area is kinetically monitored during manufacturing. What this means is, over a specific time period, a microbial air sampler is used to continuously force an already established volume of air to passover a petri dish that serves as the artificial medium containing an agar nutrient based test media
The Petri dishes containing medium are then removed from the air sampler and directly incubated. Incubation allows the collected culture that is the microorganisms such as bacteria, fungietc to grow into visible colonies that can be easilyidentified and analyzed through counting. This gives a clear indicator of how many viable microorganisms are there per cubic meter of air.

Advantages
*.It allows for both qualitative and quantitative analysis of the sample
*.Allows for faster results as devices used for thismethod allow for a shorter sampling period suchas 10 minutes
*.Ideal for controlled areas as they tend to have a low microbial concentration

2. Passive Air Sampling

Also referred to as diffusive air sampling, passive air sampling basically involves leaving settle plates or contact plates exposed to the air for a certain period of time to collect microbes that may settle onto the surfaces of the plates.Just like in the active air sampling, the plates are then incubated to allow for the microorganisms that dropped onto the plates to grow into coloniesthat can accurately be analyzed.

Advantages
*.For starters, the method is inexpensive as it does not require a lot of equipment
*.Offers average contamination levels over long sampling periods that could range from hours tomonths
*.No supervision is required during the sampling period
*.Its affordability makes it easy to sample various contamination hotspots at once

Both methods have their own advantages but none of the methods of air sampling given above is optional butboth are mandatorybecause both of them give different information about the air in theclassified area.

As I mentioned above in active air sampling we determine bioburden in 1 cubic meter area and wesample 1000 liters of air by air sampler while in passive air sampling we determine that how much microbes settle in 90 mm diameter surface of anyequipment exposed in controlled area.

A lot of pharmaceutical professionals have confusion in air sampling that which one should be done among both of samplings. But all regulatory guidelines say that it is mandatory to sample and analyze the clean room area by both methods of air sampling.

Comments

Post a Comment

Popular posts from this blog

-
What is VMP Brief information about Qualification, Validation and calibration of Equipment, Instrument and System. A document providing information on the company’s validation work programme. It should be define details of and timescales for the validation work to be performed. Responsibilities relating to the plan should be stated. 2.2 Which Guideline follow for preparation of VMP PIC/S (PI 006), WHO TRS 961, Eudralex Volume 4 2.3 Contents of VMP.  Cover Page, Table of contents  Approval of document  Introduction, Objective, Scope  Quality policy  Validation policy  Quality Risk Management Policy  Responsibility  Validation / Qualification Schematic Flow  Validation and Qualification approach  Revalidation and Requalification approach  Qualification Activity  Facility Qualification  Qualification and Validation of Utilities  Equipment Qualification  Laboratory Instruments and Equipment  Personnel Qualification  Products and Process Validation  E
http://totalpharmasoloution.blogspot.in
-
Image
Purified Water Storage and Distribution System Learn about the purified water storage and distribution system and procedure for validation. The purified water is prepared by purified water generation system (Reverse Osmosis System) and collected in purified water storage tank of required capacity and distributed by a centrifugal pump for loop recirculation.At different points of use separate heat exchangeris provided (if required) to bring down temperature of hot circulating water as and when required. There is a back pressure valve in the return line. Instruments and on/off valve are for controlling and monitoring the system  operation and water quality. These are controlled from a centralized control panel consisting of a PLC board. The distribution piping consists of sanitary tubes, fittings, valves with orbital welding and triclover clamp in manufacturing area and for instrument connections. The water through this piping is supplied to various user points and circulated back
http://totalpharmasoloution.blogspot.in